The handles may seem trivial, very unimportant parts of a drawer. But when they get worn out, damaged, or misaligned, they make it hard for you to open and close the drawer, and also ruin the appearance of your kitchen. But don’t worry, in this post, we’ll teach you step by step how to install cabinet drawer handles in Singapore.
You can do it at home without needing any professional help. But, you need to read this guide so that you do not end up making a loss during the process. Also, PS Home Maintenance Singapore provides switches & points installation, false ceiling installation, and ceiling fan and exhaust fan repair services in Singapore.
Importance of installing Cabinet Drawer Handles in Singapore
The following is the importance of installing cabinet drawer handles in Singapore:
- Improves drawer accessibility and ease of use
- Enhances the overall aesthetic of the space
- Helps protect cabinet surfaces from fingerprints and wear
- Adds a personal touch to home interiors
- Increases the resale appeal of the property
- Supports better hygiene in kitchens and bathrooms
- Offers better grip for elderly or children
- Complements existing hardware and design themes
How to Install Cabinet Drawer Handles in Singapore?
Installing a Cabinet drawer isn’t as difficult as you might think. You can do it yourself just by following this little step-by-step guide:
Step 1: Measure and Mark Handle Placement
Don’t just get to drilling, as measurement is the most important part of the process. Take a measuring tape and then measure where the handles will go. They’re usually in the centre of the drawer so that it’s easier to open and close them without colliding with one another.
Use a rule or measuring tool to find the exact midpoints horizontally and vertically, and then make holes on both of the slides. It’s a pro approach to ensure no misalignment happens when the handles are installed.
Step 2: Double-Check the Alignment
Since alignment is the most important thing, you don’t need to rush into it. Take a step back and then look at your markings to ensure they’re aligned precisely. If you’re installing multiple cabinet drawer handles, you can use a template or cardboard with the pre-measured holes to avoid any issues.
Step 3: Drill Pilot Holes Carefully
Drilling is now the part that you need to do very carefully. Without panicking, gently get a small drill around 3mm or so and then make pilot holes where you marked earlier.
Do it precisely and with gentle care, as doing it wrongly can damage the drawer and cost you a lot of money. Making the holes is important to screw in and also reduce the risks of cracking or splintering the cabinets surface.
Step 4: Fit the Handle and Insert Screws
When you’ve created the hole, then hold your handle up and to the drawer front and line it with the holes accurately. From the inside of the drawer, push the screws through and tight them into using a screwdriver.
Now, the handles should feel perfectly tightened and firm. Don’t over tighten them as they could strip the screw and dent the handle.
Step 5: Test the Handle
Congrats! You’ve successfully installed the cabinet drawer handles in Singapore by yourself. It’s now time to test them by tugging on them. Are they secure? Are they flush in the drawer?
If they’re wobbly then double check that screws are tight and perfectly placed in the holes. Sometimes, it’s not you who did wrong, but the wood itself isn’t flat. Therefore, adjust one screw slightly and it’ll make the handles perfectly fit and work fine.
Step 6: Repeat for All Drawers
Once you’ve nailed the first one, the rest are easier. Use the same measurements for the remaining drawers to keep everything consistent. Work slowly and take your time—it’s better to go drawer by drawer than to rust and regret it. A good handle setup makes your whole cabinet look way more put-together.
This is how to install cabinet drawer handles in Singapore yourself at home. Just make sure that you’re being extra careful throughout the process, especially when it’s your first time doing it. Other than that, being gentle, specifically when you’re drilling and making the hole, so that you don’t do it wrong, could save you a lot.
Get all the supplies and the required things, such as a measuring tape, a marker, new handles, and a drilling machine, ready so that you don’t have to run after the tools during the process. This will ensure that you’re fully focused on installing the cabinet drawer handles rather than finding the required tool, which will slow down the process and also divert your focus.
Final Words
How to install cabinet Drawer handles in Singapore? Measure and mark the handle placement carefully, then double-check alignment with a ruler or template. Drill small pilot holes, position the handle, insert screws from inside the drawer, tighten them gently, test for stability, and repeat the process for all other drawers to keep everything looking neat and consistent.